Проблема с 802.11ac с карты WLE900VX (QCA9880 ath10k) через hostapd
Думаю, здесь я ошибаюсь... Но я не уверен, действительно ли это проблема, и даже если это так, я не уверен, что с этим делать.
nl80211: Could not configure driver mode
nl80211: deinit ifname=wlp6s0 disabled_11b_rates=0
nl80211: Remove monitor interface: refcount=0
nl80211: Remove beacon (ifindex=8)
netlink: Operstate: ifindex=8 linkmode=0 (kernel-control), operstate=6 (IF_OPER_UP)
nl80211 driver initialization failed.
Я вроде как исключил, что он физически не работает, используя гораздо менее оптимальную конфигурацию - я увидел, что он появился в списке доступных интернет-соединений на моем ноутбуке и подключился - на беспроводной скорости 54mbps. Хотелось бы мне сделать .bak-файл этой конфигурации, но я этого не сделал. Даже если бы я это сделал, я играю с оборудованием 802.11ac, потому что хочу, чтобы оно работало быстрее.
Да, я мог бы купить что-то с полки, и это было бы здорово. Сетевые технологии не входят в мой основной набор навыков. Создание маршрутизатора на базе x86 было приятным отвлечением от требований жизни, хобби, и по большей части это весело. Но я снова застрял и не уверен, как поступить на этот раз.
Ниже я опубликую тонну вещей, которые вам, вероятно, даже не нужны... Я буду рад разместить все остальное, что поможет вам помочь мне. Я ценю, что вы нашли время, чтобы прочитать мою проблему. Еще раз спасибо.
Вот результат запуска службы hostapd с файлом wlp6s0.conf, в котором указаны характеристики карты WLE900VX 802.11ac:
root@gate:/etc/hostapd# service hostapd stop && echo "==================================================================" && hostapd -dddddB /etc/hostapd/wlp6s0.conf
==================================================================
random: Trying to read entropy from /dev/random
Configuration file: /etc/hostapd/wlp6s0.conf
ctrl_interface_group=0
rfkill: initial event: idx=0 type=1 op=0 soft=0 hard=0
rfkill: initial event: idx=1 type=1 op=0 soft=0 hard=0
nl80211: Supported cipher 00-0f-ac:1
nl80211: Supported cipher 00-0f-ac:5
nl80211: Supported cipher 00-0f-ac:2
nl80211: Supported cipher 00-0f-ac:4
nl80211: Supported cipher 00-0f-ac:6
nl80211: Using driver-based off-channel TX
nl80211: interface wlp6s0 in phy phy0
nl80211: Set mode ifindex 8 iftype 3 (AP)
nl80211: Setup AP(wlp6s0) - device_ap_sme=0 use_monitor=0
nl80211: Subscribe to mgmt frames with AP handle 0x558ab92af100
nl80211: Register frame type=0xb0 (WLAN_FC_STYPE_AUTH)
nl_handle=0x558ab92af100 match=
nl80211: Register frame command failed (type=176): ret=-114 (Operation already in progress)
nl80211: Register frame match - hexdump(len=0): [NULL]
nl80211: Could not configure driver mode
nl80211: deinit ifname=wlp6s0 disabled_11b_rates=0
nl80211: Remove monitor interface: refcount=0
nl80211: Remove beacon (ifindex=8)
netlink: Operstate: ifindex=8 linkmode=0 (kernel-control), operstate=6 (IF_OPER_UP)
nl80211 driver initialization failed.
hostapd_interface_deinit_free(0x558ab92ae710)
hostapd_interface_deinit_free: num_bss=1 conf->num_bss=1
hostapd_interface_deinit(0x558ab92ae710)
wlp6s0: interface state UNINITIALIZED->DISABLED
hostapd_bss_deinit: deinit bss wlp6s0
wlp6s0: AP-DISABLED
hostapd_cleanup(hapd=0x558ab92af900 (wlp6s0))
hostapd_free_hapd_data: Interface wlp6s0 wasn't started
hostapd_interface_deinit_free: driver=(nil) drv_priv=(nil) ->
hapd_deinit
hostapd_interface_free(0x558ab92ae710)
hostapd_interface_free: free hapd 0x558ab92af900
hostapd_cleanup_iface(0x558ab92ae710)
hostapd_cleanup_iface_partial(0x558ab92ae710)
hostapd_cleanup_iface: free iface=0x558ab92ae710
Здесь у меня определены некоторые интерфейсы:
root@gate:/etc/network# tail -n1000 interfaces
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
source /etc/network/interfaces.d/*
# The loopback network interface
auto lo
iface lo inet loopback
pre-up iptables-restore < /etc/iptables.rules
# The primary network interface
auto enp7s0
iface enp7s0 inet dhcp
# Wireless interfaces
auto wlp1s0
iface wlp1s0 inet static
address 192.168.1.220
netmask 255.255.255.0
auto wlp6s0
iface wlp6s0 inet static
address 192.168.1.230
netmask 255.255.255.0
Вот вывод ifconfig:
root@gate:/etc/hostapd# ifconfig
enp7s0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 192.168.1.103 netmask 255.255.255.0 broadcast 192.168.1.255
inet6 fe80::d250:99ff:fe5c:3a18 prefixlen 64 scopeid 0x20<link>
ether d0:50:99:5c:3a:18 txqueuelen 1000 (Ethernet)
RX packets 8900 bytes 7106294 (6.7 MiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 1484 bytes 183661 (179.3 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 1 (Local Loopback)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
wlp1s0: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
inet 192.168.1.220 netmask 255.255.255.0 broadcast 192.168.1.255
ether e4:ce:8f:52:2a:23 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
wlp6s0: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
inet 192.168.1.230 netmask 255.255.255.0 broadcast 192.168.1.255
inet6 fe80::6f0:21ff:fe18:4a2 prefixlen 64 scopeid 0x20<link>
ether 04:f0:21:18:04:a2 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 12 bytes 1144 (1.1 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
Думаю, мой файл wlp6s0.conf с приправой hostapd.conf имеет значение:
root@gate:/etc/hostapd# tail -n1000 wlp6s0.conf
interface=wlp6s0
driver=nl80211
hw_mode=a
channel=0
ssid=q2900mac
auth_algs=1
wmm_enabled=1
ieee80211d=1
country_code=US
wpa=2
wpa_key_mgmt=WPA-PSK
wpa_pairwise=TKIP CCMP
rsn_pairwise=TKIP
wpa_passphrase=password
ieee80211n=1
ht_capab=[HT40+][SHORT-GI-40][TX-STBC][RX-STBC1][DSSS_CK-40][LDPC][MAX-AMSDU-3839]
ieee80211ac=1
vht_capab=[MAX-MPDU-11454][RXLDPC][SHORT-GI-80][TX-STBC-2BY1][RX-STBC-1][MAX-A-MPDU-LEN-EXP7][TX-ANTENNA-PATTERN][RX-ANTENNA-PATTERN]
vht_oper_chwidth=1
vht_oper_centr_freq_seg0_idx=42
ctrl_interface=/var/run/wlp6s0
ctrl_interface_group=0
Это вроде как совпадает с информацией из iw list:
root@gate:/etc/hostapd# iw list
Wiphy phy0
max # scan SSIDs: 16
max scan IEs length: 195 bytes
max # sched scan SSIDs: 0
max # match sets: 0
max # scan plans: 1
max scan plan interval: -1
max scan plan iterations: 0
Retry short limit: 7
Retry long limit: 4
Coverage class: 0 (up to 0m)
Device supports RSN-IBSS.
Device supports AP-side u-APSD.
Supported Ciphers:
* WEP40 (00-0f-ac:1)
* WEP104 (00-0f-ac:5)
* TKIP (00-0f-ac:2)
* CCMP-128 (00-0f-ac:4)
* CMAC (00-0f-ac:6)
Available Antennas: TX 0x7 RX 0x7
Configured Antennas: TX 0x7 RX 0x7
Supported interface modes:
* managed
* AP
* AP/VLAN
* monitor
* mesh point
Band 1:
Capabilities: 0x19ef
RX LDPC
HT20/HT40
SM Power Save disabled
RX HT20 SGI
RX HT40 SGI
TX STBC
RX STBC 1-stream
Max AMSDU length: 7935 bytes
DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 8 usec (0x06)
HT TX/RX MCS rate indexes supported: 0-23
Bitrates (non-HT):
* 1.0 Mbps
* 2.0 Mbps (short preamble supported)
* 5.5 Mbps (short preamble supported)
* 11.0 Mbps (short preamble supported)
* 6.0 Mbps
* 9.0 Mbps
* 12.0 Mbps
* 18.0 Mbps
* 24.0 Mbps
* 36.0 Mbps
* 48.0 Mbps
* 54.0 Mbps
Frequencies:
* 2412 MHz [1] (30.0 dBm)
* 2417 MHz [2] (30.0 dBm)
* 2422 MHz [3] (30.0 dBm)
* 2427 MHz [4] (30.0 dBm)
* 2432 MHz [5] (30.0 dBm)
* 2437 MHz [6] (30.0 dBm)
* 2442 MHz [7] (30.0 dBm)
* 2447 MHz [8] (30.0 dBm)
* 2452 MHz [9] (30.0 dBm)
* 2457 MHz [10] (30.0 dBm)
* 2462 MHz [11] (30.0 dBm)
* 2467 MHz [12] (disabled)
* 2472 MHz [13] (disabled)
* 2484 MHz [14] (disabled)
Band 2:
Capabilities: 0x19ef
RX LDPC
HT20/HT40
SM Power Save disabled
RX HT20 SGI
RX HT40 SGI
TX STBC
RX STBC 1-stream
Max AMSDU length: 7935 bytes
DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 8 usec (0x06)
HT TX/RX MCS rate indexes supported: 0-23
VHT Capabilities (0x338001b2):
Max MPDU length: 11454
Supported Channel Width: neither 160 nor 80+80
RX LDPC
short GI (80 MHz)
TX STBC
RX antenna pattern consistency
TX antenna pattern consistency
VHT RX MCS set:
1 streams: MCS 0-9
2 streams: MCS 0-9
3 streams: MCS 0-9
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
VHT RX highest supported: 0 Mbps
VHT TX MCS set:
1 streams: MCS 0-9
2 streams: MCS 0-9
3 streams: MCS 0-9
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
VHT TX highest supported: 0 Mbps
Bitrates (non-HT):
* 6.0 Mbps
* 9.0 Mbps
* 12.0 Mbps
* 18.0 Mbps
* 24.0 Mbps
* 36.0 Mbps
* 48.0 Mbps
* 54.0 Mbps
Frequencies:
* 5180 MHz [36] (23.0 dBm)
* 5200 MHz [40] (23.0 dBm)
* 5220 MHz [44] (23.0 dBm)
* 5240 MHz [48] (23.0 dBm)
* 5260 MHz [52] (23.0 dBm) (no IR, radar detection)
* 5280 MHz [56] (23.0 dBm) (no IR, radar detection)
* 5300 MHz [60] (23.0 dBm) (no IR, radar detection)
* 5320 MHz [64] (23.0 dBm) (no IR, radar detection)
* 5500 MHz [100] (23.0 dBm) (no IR, radar detection)
* 5520 MHz [104] (23.0 dBm) (no IR, radar detection)
* 5540 MHz [108] (23.0 dBm) (no IR, radar detection)
* 5560 MHz [112] (23.0 dBm) (no IR, radar detection)
* 5580 MHz [116] (23.0 dBm) (no IR, radar detection)
* 5600 MHz [120] (23.0 dBm) (no IR, radar detection)
* 5620 MHz [124] (23.0 dBm) (no IR, radar detection)
* 5640 MHz [128] (23.0 dBm) (no IR, radar detection)
* 5660 MHz [132] (23.0 dBm) (no IR, radar detection)
* 5680 MHz [136] (23.0 dBm) (no IR, radar detection)
* 5700 MHz [140] (23.0 dBm) (no IR, radar detection)
* 5720 MHz [144] (23.0 dBm) (radar detection)
* 5745 MHz [149] (30.0 dBm)
* 5765 MHz [153] (30.0 dBm)
* 5785 MHz [157] (30.0 dBm)
* 5805 MHz [161] (30.0 dBm)
* 5825 MHz [165] (30.0 dBm)
Supported commands:
* new_interface
* set_interface
* new_key
* start_ap
* new_station
* new_mpath
* set_mesh_config
* set_bss
* authenticate
* associate
* deauthenticate
* disassociate
* join_ibss
* join_mesh
* remain_on_channel
* set_tx_bitrate_mask
* frame
* frame_wait_cancel
* set_wiphy_netns
* set_channel
* set_wds_peer
* probe_client
* set_noack_map
* register_beacons
* start_p2p_device
* set_mcast_rate
* channel_switch
* set_qos_map
* connect
* disconnect
Supported TX frame types:
* IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-device: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
Supported RX frame types:
* IBSS: 0x40 0xb0 0xc0 0xd0
* managed: 0x40 0xd0
* AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* mesh point: 0xb0 0xc0 0xd0
* P2P-client: 0x40 0xd0
* P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* P2P-device: 0x40 0xd0
software interface modes (can always be added):
* AP/VLAN
* monitor
valid interface combinations:
* #{ AP, mesh point } <= 8, #{ managed } <= 1,
total <= 8, #channels <= 1, STA/AP BI must match
HT Capability overrides:
* MCS: ff ff ff ff ff ff ff ff ff ff
* maximum A-MSDU length
* supported channel width
* short GI for 40 MHz
* max A-MPDU length exponent
* min MPDU start spacing
Device supports TX status socket option.
Device supports HT-IBSS.
Device supports SAE with AUTHENTICATE command
Device supports scan flush.
Device supports AP scan.
Device supports per-vif TX power setting
Driver supports full state transitions for AP/GO clients
Driver supports a userspace MPM
Driver/device bandwidth changes during BSS lifetime (AP/GO mode)
Device supports static SMPS
Device supports configuring vdev MAC-addr on create.
Device supports VHT-IBSS.
Wiphy phy1
max # scan SSIDs: 4
max scan IEs length: 2257 bytes
max # sched scan SSIDs: 0
max # match sets: 0
max # scan plans: 1
max scan plan interval: -1
max scan plan iterations: 0
Retry short limit: 7
Retry long limit: 4
Coverage class: 0 (up to 0m)
Device supports RSN-IBSS.
Device supports AP-side u-APSD.
Device supports T-DLS.
Supported Ciphers:
* WEP40 (00-0f-ac:1)
* WEP104 (00-0f-ac:5)
* TKIP (00-0f-ac:2)
* CCMP-128 (00-0f-ac:4)
* CCMP-256 (00-0f-ac:10)
* GCMP-128 (00-0f-ac:8)
* GCMP-256 (00-0f-ac:9)
* CMAC (00-0f-ac:6)
* CMAC-256 (00-0f-ac:13)
* GMAC-128 (00-0f-ac:11)
* GMAC-256 (00-0f-ac:12)
Available Antennas: TX 0x7 RX 0x7
Configured Antennas: TX 0x7 RX 0x7
Supported interface modes:
* IBSS
* managed
* AP
* AP/VLAN
* WDS
* monitor
* mesh point
* P2P-client
* P2P-GO
* outside context of a BSS
Band 1:
Capabilities: 0x11ef
RX LDPC
HT20/HT40
SM Power Save disabled
RX HT20 SGI
RX HT40 SGI
TX STBC
RX STBC 1-stream
Max AMSDU length: 3839 bytes
DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 8 usec (0x06)
HT TX/RX MCS rate indexes supported: 0-23
Bitrates (non-HT):
* 1.0 Mbps
* 2.0 Mbps (short preamble supported)
* 5.5 Mbps (short preamble supported)
* 11.0 Mbps (short preamble supported)
* 6.0 Mbps
* 9.0 Mbps
* 12.0 Mbps
* 18.0 Mbps
* 24.0 Mbps
* 36.0 Mbps
* 48.0 Mbps
* 54.0 Mbps
Frequencies:
* 2412 MHz [1] (15.0 dBm)
* 2417 MHz [2] (15.0 dBm)
* 2422 MHz [3] (15.0 dBm)
* 2427 MHz [4] (15.0 dBm)
* 2432 MHz [5] (15.0 dBm)
* 2437 MHz [6] (15.0 dBm)
* 2442 MHz [7] (15.0 dBm)
* 2447 MHz [8] (15.0 dBm)
* 2452 MHz [9] (15.0 dBm)
* 2457 MHz [10] (15.0 dBm)
* 2462 MHz [11] (15.0 dBm)
* 2467 MHz [12] (disabled)
* 2472 MHz [13] (disabled)
* 2484 MHz [14] (disabled)
Band 2:
Capabilities: 0x11ef
RX LDPC
HT20/HT40
SM Power Save disabled
RX HT20 SGI
RX HT40 SGI
TX STBC
RX STBC 1-stream
Max AMSDU length: 3839 bytes
DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 8 usec (0x06)
HT TX/RX MCS rate indexes supported: 0-23
Bitrates (non-HT):
* 6.0 Mbps
* 9.0 Mbps
* 12.0 Mbps
* 18.0 Mbps
* 24.0 Mbps
* 36.0 Mbps
* 48.0 Mbps
* 54.0 Mbps
Frequencies:
* 5180 MHz [36] (15.0 dBm)
* 5200 MHz [40] (15.0 dBm) (no IR)
* 5220 MHz [44] (15.0 dBm) (no IR)
* 5240 MHz [48] (15.0 dBm) (no IR)
* 5260 MHz [52] (16.0 dBm) (no IR, radar detection)
* 5280 MHz [56] (16.0 dBm) (no IR, radar detection)
* 5300 MHz [60] (16.0 dBm) (no IR, radar detection)
* 5320 MHz [64] (16.0 dBm) (no IR, radar detection)
* 5500 MHz [100] (disabled)
* 5520 MHz [104] (disabled)
* 5540 MHz [108] (disabled)
* 5560 MHz [112] (disabled)
* 5580 MHz [116] (disabled)
* 5600 MHz [120] (disabled)
* 5620 MHz [124] (disabled)
* 5640 MHz [128] (disabled)
* 5660 MHz [132] (disabled)
* 5680 MHz [136] (disabled)
* 5700 MHz [140] (disabled)
* 5745 MHz [149] (20.0 dBm)
* 5765 MHz [153] (20.0 dBm) (no IR)
* 5785 MHz [157] (20.0 dBm) (no IR)
* 5805 MHz [161] (20.0 dBm) (no IR)
* 5825 MHz [165] (20.0 dBm) (no IR)
Supported commands:
* new_interface
* set_interface
* new_key
* start_ap
* new_station
* new_mpath
* set_mesh_config
* set_bss
* authenticate
* associate
* deauthenticate
* disassociate
* join_ibss
* join_mesh
* remain_on_channel
* set_tx_bitrate_mask
* frame
* frame_wait_cancel
* set_wiphy_netns
* set_channel
* set_wds_peer
* tdls_mgmt
* tdls_oper
* probe_client
* set_noack_map
* register_beacons
* start_p2p_device
* set_mcast_rate
* channel_switch
* set_qos_map
* connect
* disconnect
Supported TX frame types:
* IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-device: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
Supported RX frame types:
* IBSS: 0x40 0xb0 0xc0 0xd0
* managed: 0x40 0xd0
* AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* mesh point: 0xb0 0xc0 0xd0
* P2P-client: 0x40 0xd0
* P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* P2P-device: 0x40 0xd0
software interface modes (can always be added):
* AP/VLAN
* monitor
valid interface combinations:
* #{ managed } <= 2048, #{ AP, mesh point } <= 8, #{ P2P-client, P2P-GO } <= 1,
total <= 2048, #channels <= 1, STA/AP BI must match
* #{ WDS } <= 2048,
total <= 2048, #channels <= 1, STA/AP BI must match
HT Capability overrides:
* MCS: ff ff ff ff ff ff ff ff ff ff
* maximum A-MSDU length
* supported channel width
* short GI for 40 MHz
* max A-MPDU length exponent
* min MPDU start spacing
Device supports TX status socket option.
Device supports HT-IBSS.
Device supports SAE with AUTHENTICATE command
Device supports low priority scan.
Device supports scan flush.
Device supports AP scan.
Device supports per-vif TX power setting
P2P GO supports CT window setting
Driver supports full state transitions for AP/GO clients
Driver supports a userspace MPM
Device supports active monitor (which will ACK incoming frames)
Driver/device bandwidth changes during BSS lifetime (AP/GO mode)
Device supports configuring vdev MAC-addr on create.
0
задан BradChesney79
24 January 2018 в 23:14
Ссылка
3 ответа
Для следующего бедного сока, которое случится вместе ...
Это мой файл hostapd.conf для эталонной платы XB140 на базе карты Compex WLE900VX QCA9880:
interface=wlp6s0
driver=nl80211
hw_mode=a
ctrl_interface=/var/run/wlp6s0
ctrl_interface_group=0
max_num_sta=255
#logger_syslog=-1
#logger_syslog_level=2
#logger_stdout=-1
#logger_stdout_level=2
#Details for Connecting Clients via WPA2 TKIP
ssid=q2900mAC
auth_algs=1
wpa=2
wpa_key_mgmt=WPA-PSK
wpa_pairwise=CCMP
rsn_pairwise=CCMP
wpa_passphrase=password
#802.11d Regulatory Restrictions Designations for Which Frequencies and Channels are Legal
ieee80211d=1
country_code=US
#802.11n Configurations
ieee80211n=1
ht_capab=[LDPC][HT40+][SHORT-GI-20][SHORT-GI-40][TX-STBC][DSSS_CCK-40]
#802.11ac Configurations
ieee80211ac=1
vht_capab=[SHORT-GI-80][MAX-MPDU-11454][RXLDPC][TX-STBC-2BY1][MAX-A-MPDU-LEN-EXP3][RX-ANTENNA-PATTERN][TX-ANTENNA-PATTERN]
vht_oper_chwidth=1
#How Many Units of Time Between Beacon Transmissions
beacon_int=100
#Multiplier of How Many Units of Time Between Beacon Transmissions
dtim_period=2
#(e.g. 100 milliseconds(ms) * 2 = 200 ms between beacons)
#Something About WMM Clients Needing this
wmm_enabled=1
###To Be Completely Honest-- I'm Not Entirely Certain What the Rest of this file does
#QoS Type of Traffic Management Based on Traffic Type
#Background
wmm_ac_bk_cwmin=4
wmm_ac_bk_cwmax=10
wmm_ac_bk_aifs=7
wmm_ac_bk_txop_limit=0
wmm_ac_bk_acm=0
#Best Effort
wmm_ac_be_aifs=3
wmm_ac_be_cwmin=4
wmm_ac_be_cwmax=10
wmm_ac_be_txop_limit=0
wmm_ac_be_acm=0
#Video
wmm_ac_vi_aifs=2
wmm_ac_vi_cwmin=3
wmm_ac_vi_cwmax=4
wmm_ac_vi_txop_limit=94
wmm_ac_vi_acm=0
#Voice
wmm_ac_vo_aifs=2
wmm_ac_vo_cwmin=2
wmm_ac_vo_cwmax=3
wmm_ac_vo_txop_limit=47
wmm_ac_vo_acm=0
Кроме того, если вы застрял на 54 Мбит / с - скорость 802.11g - мне нужно было установить пакет wpa_supplicant . Мой Samsung Note8 со скоростью 650 Мбит / с с этой конфигурацией. Я еще не измерил реальную пропускную способность.
И последнее, но не менее важное: этот ответ никогда бы не появился без самоотверженных героев по адресу http://lists.infradead.org/mailman/listinfo/hostap
Dank je JC! Дополнительный совет, который мне передали: карта Compex WLE1216v5-20 MIMO x 4 лучше ... https://www.compex.com.sg/product/wle1216v5-20/ (я не могу подтвердить пока что, но чего стоит.)
0
Это «ответ». Это неправильно, но я превысил ограничение в 30 000 символов, пытаясь добавить его к вопросу выше.
Следующая базовая конфигурация "работает"; Я вижу сеть Wi-Fi и подключаюсь:
interface=wlan0
driver=nl80211
ssid=ath10k
hw_mode=a
channel=36
ieee80211n=0
ieee80211ac=0
Результат выглядит следующим образом:
root@gate:/etc/hostapd# service hostapd stop && echo "==================================================================" && hostapd -dddddB /etc/hostapd/basic.conf
==================================================================
random: Trying to read entropy from /dev/random
Configuration file: /etc/hostapd/basic.conf
rfkill: initial event: idx=0 type=1 op=0 soft=0 hard=0
rfkill: initial event: idx=1 type=1 op=0 soft=0 hard=0
nl80211: Supported cipher 00-0f-ac:1
nl80211: Supported cipher 00-0f-ac:5
nl80211: Supported cipher 00-0f-ac:2
nl80211: Supported cipher 00-0f-ac:4
nl80211: Supported cipher 00-0f-ac:6
nl80211: Using driver-based off-channel TX
nl80211: interface wlp6s0 in phy phy0
nl80211: Set mode ifindex 8 iftype 3 (AP)
nl80211: Failed to set interface 8 to mode 3: -16 (Device or resource busy)
nl80211: Try mode change after setting interface down
nl80211: Set mode ifindex 8 iftype 3 (AP)
nl80211: Mode change succeeded while interface is down
nl80211: Setup AP(wlp6s0) - device_ap_sme=0 use_monitor=0
nl80211: Subscribe to mgmt frames with AP handle 0x558199f770c0
nl80211: Register frame type=0xb0 (WLAN_FC_STYPE_AUTH) nl_handle=0x558199f770c0 match=
nl80211: Register frame type=0x0 (WLAN_FC_STYPE_ASSOC_REQ) nl_handle=0x558199f770c0 match=
nl80211: Register frame type=0x20 (WLAN_FC_STYPE_REASSOC_REQ) nl_handle=0x558199f770c0 match=
nl80211: Register frame type=0xa0 (WLAN_FC_STYPE_DISASSOC) nl_handle=0x558199f770c0 match=
nl80211: Register frame type=0xc0 (WLAN_FC_STYPE_DEAUTH) nl_handle=0x558199f770c0 match=
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x558199f770c0 match=
nl80211: Register frame type=0x40 (WLAN_FC_STYPE_PROBE_REQ) nl_handle=0x558199f770c0 match=
nl80211: Add own interface ifindex 8
nl80211: if_indices[16]: 8
phy: phy0
BSS count 1, BSSID mask 00:00:00:00:00:00 (0 bits)
nl80211: Regulatory information - country=US (DFS-FCC)
nl80211: 2402-2472 @ 40 MHz 30 mBm
nl80211: 5170-5250 @ 80 MHz 23 mBm
nl80211: 5250-5330 @ 80 MHz 23 mBm (DFS)
nl80211: 5490-5730 @ 160 MHz 23 mBm (DFS)
nl80211: 5735-5835 @ 80 MHz 30 mBm
nl80211: 57240-63720 @ 2160 MHz 40 mBm
nl80211: Added 802.11b mode based on 802.11g information
Allowed channel: mode=1 chan=1 freq=2412 MHz max_tx_power=30 dBm
Allowed channel: mode=1 chan=2 freq=2417 MHz max_tx_power=30 dBm
Allowed channel: mode=1 chan=3 freq=2422 MHz max_tx_power=30 dBm
Allowed channel: mode=1 chan=4 freq=2427 MHz max_tx_power=30 dBm
Allowed channel: mode=1 chan=5 freq=2432 MHz max_tx_power=30 dBm
Allowed channel: mode=1 chan=6 freq=2437 MHz max_tx_power=30 dBm
Allowed channel: mode=1 chan=7 freq=2442 MHz max_tx_power=30 dBm
Allowed channel: mode=1 chan=8 freq=2447 MHz max_tx_power=30 dBm
Allowed channel: mode=1 chan=9 freq=2452 MHz max_tx_power=30 dBm
Allowed channel: mode=1 chan=10 freq=2457 MHz max_tx_power=30 dBm
Allowed channel: mode=1 chan=11 freq=2462 MHz max_tx_power=30 dBm
Allowed channel: mode=2 chan=36 freq=5180 MHz max_tx_power=23 dBm
Allowed channel: mode=2 chan=40 freq=5200 MHz max_tx_power=23 dBm
Allowed channel: mode=2 chan=44 freq=5220 MHz max_tx_power=23 dBm
Allowed channel: mode=2 chan=48 freq=5240 MHz max_tx_power=23 dBm
Allowed channel: mode=2 chan=149 freq=5745 MHz max_tx_power=30 dBm
Allowed channel: mode=2 chan=153 freq=5765 MHz max_tx_power=30 dBm
Allowed channel: mode=2 chan=157 freq=5785 MHz max_tx_power=30 dBm
Allowed channel: mode=2 chan=161 freq=5805 MHz max_tx_power=30 dBm
Allowed channel: mode=2 chan=165 freq=5825 MHz max_tx_power=30 dBm
Allowed channel: mode=0 chan=1 freq=2412 MHz max_tx_power=30 dBm
Allowed channel: mode=0 chan=2 freq=2417 MHz max_tx_power=30 dBm
Allowed channel: mode=0 chan=3 freq=2422 MHz max_tx_power=30 dBm
Allowed channel: mode=0 chan=4 freq=2427 MHz max_tx_power=30 dBm
Allowed channel: mode=0 chan=5 freq=2432 MHz max_tx_power=30 dBm
Allowed channel: mode=0 chan=6 freq=2437 MHz max_tx_power=30 dBm
Allowed channel: mode=0 chan=7 freq=2442 MHz max_tx_power=30 dBm
Allowed channel: mode=0 chan=8 freq=2447 MHz max_tx_power=30 dBm
Allowed channel: mode=0 chan=9 freq=2452 MHz max_tx_power=30 dBm
Allowed channel: mode=0 chan=10 freq=2457 MHz max_tx_power=30 dBm
Allowed channel: mode=0 chan=11 freq=2462 MHz max_tx_power=30 dBm
Completing interface initialization
Mode: IEEE 802.11a Channel: 36 Frequency: 5180 MHz
DFS 0 channels required radar detection
nl80211: Set freq 5180 (ht_enabled=0, vht_enabled=0, bandwidth=20 MHz, cf1=5180 MHz, cf2=0 MHz)
* freq=5180
* vht_enabled=0
* ht_enabled=0
RATE[0] rate=60 flags=0x1
RATE[1] rate=90 flags=0x0
RATE[2] rate=120 flags=0x1
RATE[3] rate=180 flags=0x0
RATE[4] rate=240 flags=0x1
RATE[5] rate=360 flags=0x0
RATE[6] rate=480 flags=0x0
RATE[7] rate=540 flags=0x0
hostapd_setup_bss(hapd=0x558199f77900 (wlp6s0), first=1)
wlp6s0: Flushing old station entries
nl80211: flush -> DEL_STATION wlp6s0 (all)
wlp6s0: Deauthenticate all stations
nl80211: send_mlme - da= ff:ff:ff:ff:ff:ff noack=0 freq=0 no_cck=0 offchanok=0 wait_time=0 fc=0xc0 (WLAN_FC_STYPE_DEAUTH) nlmode=3
nl80211: send_mlme -> send_frame
nl80211: send_frame - Use bss->freq=5180
nl80211: send_frame -> send_frame_cmd
nl80211: CMD_FRAME freq=5180 wait=0 no_cck=0 no_ack=0 offchanok=0
CMD_FRAME - hexdump(len=26): c0 00 00 00 ff ff ff ff ff ff 04 f0 21 18 04 a2 04 f0 21 18 04 a2 00 00 02 00
nl80211: Frame command failed: ret=-16 (Device or resource busy) (freq=5180 wait=0)
wpa_driver_nl80211_set_key: ifindex=8 (wlp6s0) alg=0 addr=(nil) key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=8 (wlp6s0) alg=0 addr=(nil) key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=8 (wlp6s0) alg=0 addr=(nil) key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=8 (wlp6s0) alg=0 addr=(nil) key_idx=3 set_tx=0 seq_len=0 key_len=0
Using interface wlp6s0 with hwaddr 04:f0:21:18:04:a2 and ssid "ath10k"
nl80211: Set beacon (beacon_set=0)
nl80211: Beacon head - hexdump(len=57): 80 00 00 00 ff ff ff ff ff ff 04 f0 21 18 04 a2 04 f0 21 18 04 a2 00 00 00 00 00 00 00 00 00 00 64 00 01 00 00 06 61 74 68 31 30 6b 01 08 8c 12 98 24 b0 48 60 6c 03 01 24
nl80211: Beacon tail - hexdump(len=10): 7f 08 04 00 00 02 00 00 00 40
nl80211: ifindex=8
nl80211: beacon_int=100
nl80211: dtim_period=2
nl80211: ssid - hexdump_ascii(len=6):
61 74 68 31 30 6b ath10k
* beacon_int=100
nl80211: hidden SSID not in use
nl80211: privacy=0
nl80211: auth_algs=0x3
nl80211: wpa_version=0x0
nl80211: key_mgmt_suites=0x4
nl80211: pairwise_ciphers=0x1
nl80211: group_cipher=0x1
nl80211: beacon_ies - hexdump(len=10): 7f 08 04 00 00 02 00 00 00 40
nl80211: proberesp_ies - hexdump(len=10): 7f 08 04 00 00 02 00 00 00 40
nl80211: assocresp_ies - hexdump(len=10): 7f 08 04 00 00 02 00 00 00 40
nl80211: Set wlp6s0 operstate 0->1 (UP)
netlink: Operstate: ifindex=8 linkmode=-1 (no change), operstate=6 (IF_OPER_UP)
wlp6s0: interface state UNINITIALIZED->ENABLED
wlp6s0: AP-ENABLED
wlp6s0: Setup of interface done.
ctrl_iface not configured!
0
Wel, sportliefhebbers - dit lyk asof u hostapd stop, dit is nie genoeg om die verifikasie-rame wat voorheen geregistreer is, vry te stel nie. Dit keer dat my hostapd-diens nie kan misluk nie - so ek gaan dit as die antwoord merk.
apt install psmisc
killall hostapd
root@gate:/etc/hostapd# service hostapd stop && echo "==================================================================" && hostapd -dddddB /etc/hostapd/wlp6s0.conf
Bing, bang, boom, ek kry 'n verbinding! ... teen 54 Mbps. Dus, nog steeds nie reg nie. Beter, funksioneel. Maar, geen sigaar nie. Dit lyk asof daar meer koeiklok nodig is.
Waar het u die wenk gekry om dit te doen? Ek sal jou vertel. Ek het hierdie poslys van 2012 gevind:
Op 08/11/2012 07:39 het Jouni Malinen geskryf:
Op Wo 11 Julie 2012 om 02:21:40 PM -0700, Ben Greear het geskryf:
Kernel is 3.3.8+, hostapd is van 'n paar dae gelede. Enige idee waarom dit misluk?
1342041584.536008: nl80211: Teken in op mgmt-rame met AP-handvatsel 0x9a97900 1342041584.536052: nl80211: Registreer raamtipe = 0xb0 nl_handle = 0x9a97900 1342041584.536075: nl80211: Registreer raampassing - hexdump (len = 0): [NULL] 1342041584.536177: nl80211: Registerraamopdrag misluk (tipe = 176): ret = -114 (bewerking reeds aan die gang) 1342041584.536201: nl80211: Registreer raampassing - hexdump (len = 0): [NULL] 1342041584.536263: nl80211: Kon nie koppelvlak vap0 in AP-modus stel nie
Die bestuurder het blykbaar nie die versoek aanvaar om vir verwerking te registreer nie Verifikasie-rame as gevolg van iets anders waarvoor reeds geregistreer is dié. Het u 'n paar ander koppelvlakke gehad wat terselfdertyd as 'n AP uitgevoer is? tyd?
Ja, dit blyk die probleem te wees. Ek het 'n paar ou hostapd-prosesse laat loop. Ek vermoor hulle nou harder..en het nog geen probleme gesien nie onlangs.
Dankie, Ben
0